Visual Weld Inspection Criteria



Visual examination of weld joint is an important activity, carried out to check the integrity and soundness of the weldment. It is an economical activity, as it doesn’t require any costly equipment. It must be carried out by a well experienced inspector. Main responsibilities of a welding inspector are:

  • Code compliance
  • Workmanship control
  • Documentation Control

The requirements of visual examination are:

All courses may be followed by a CSWIP Visual Welding Inspector examination for candidates with appropriate experience as specified in CSWIP document WI-6-92 ENTRY REQUIREMENTS There are no specific entry requirements for this course, but it is recommended that candidates have at least 6 months’ welding-related engineering experience and 2 years’ industrial experience. When conducting remote inspection the use of visual aids such as telescopes, bore scopes, fiber scopes, cameras, or other suitable instruments shall be used. Such systems shall have a resolution capability at least equivalent to that obtainable by direct visual observation.

  1. Illumination should be at least 350 Lux (minimum) but it is recommended to carry out visual inspection at an illumination of more than 500 Lux.
  2. The inspectors eye should be within the radii of 600 mm of the surface of item being inspected and the viewing angle must not be less than 30 degrees.
Visual Weld Inspection Criteria

(Also read Thickness range for welder qualification test)

Other aids which may be required during visual examination are:

  • Welding gauges (Figure 2a and 2b)
  • Weld gap gauges
  • Linear misalignment gauges (Hi-Low)
  • Magnifying glass (X2 to X5)
  • Mirrored boroscope or fibre optic viewing system (when access is restricted)

Visual inspection can be done at three stages;

  • Before welding,
  • During welding and
  • After welding

Before Welding: The inspector shall be familiarized with the applicable codes and standards/drawings/welding procedures (WPS and PQR). Welder qualification shall be carried out before production welding. The inspector shall confirm the material and review the MTC. Welding consumables shall also be inspected before welding. Joint preparation and alignment shall also to be checked prior to welding. After confirmation of all the parameters (as mentioned above), the welding inspector can permit the welder to start the production welding. If preheat is applicable, then the preheat temperature shall be confirmed before starting the weld.

(Figure 3 shows improper groove face and root gap, a welding inspector must see the groove preparation and root gap before welding)

During Welding: The inspector shall check the welding process and welding parameters with respect to the welding procedure specification (WPS) at any time during welding. Root run and root run dressing, interpass temperature shall be witnessed by the inspector. The welding consumables shall also be checked during welding.

(Also read How to write a welding procedure specification – WPS)

After welding: After complete welding, identification number is punched near joint. Complete visual inspection is done and any surface breaking or defect shall be repaired as per approved procedure. Following defects (or discontinuity) can be revealed by visual inspection:

(Figure 4: Welding inspector checking the weld reinforcement size by a Bridge Cam welding Gauge)

A dimensional survey shall be done to ensure the dimension of the part after welding. After satisfactory completion of welding proper documentation is prepared.

If a Post weld treatment is specified in WPS, Then the operation should be monitored and documented. Following parameters to be considered when Post weld heat treatment is required,

  1. Area to be heated
  2. Heating and cooling rates
  3. Holding temperature and duration
  4. Temperature distribution

Visual Weld Inspection Acceptance Criteria Asme

In addition to visual inspection, a number of other NDT (Non Destructive Test) methods are available to check the quality of weldment, some of the most common NDT methods are;

  1. Magnetic particle testing (MT)
  2. Electromagnetic testing (ET)
  3. Acoustic emission testing (AET)

Each NDT methods has its own significance and importance for example Liquid penetrant testing is very efficient and economical for checking surface defects, whereas, with the help of Ultrasonic test and Radiography test, entire depth of the weld can be inspected.

Visual Weld Inspection Criteria

Selection of NDT methods depend on the requirements. Person engaged or assigned to carry out these tests must possess the necessary qualification. A written test procedure, format for reporting and the applicable code must also be decided before conducting the examination.

Also read P-number, F-number and A-number in welding (ASME Section IX)

Visual Weld Inspection Criteria Template

Note: I had written this article for India welds newsletter- Vol 1:4 Oct-Dec 2018. Click here to read that newsletter.